This information is to supplement the Holley wiring video below. These are some of the major connections you will need to make to make your Holley Terminator X max function in the e9x/e8x chassis. As variations are found will update this page.
The wiring that is left on the chassis side after the engine harness is removed will be slightly different based on if that car was automatic or manual, and they year of the car. The basic breakdowns are found below.
Pre 03/07 (n54/n52) - x60001 (long 26 pin DME connector), three 8 pin connectors: x6031, x6021, x6011
Pre 03/07 (n54/n52) - x60001
Post 03/07 (n54/n52) - x60001
Drive By wire connections
BMW X60001 | Holley DBW Harness |
pin 7 – White/yellow | Blue - pin b tps #2 |
Pin 10 – Brown/yellow | Black – pin a/d sensor ground |
Pint 11 – Yellow | Orange – pin c/f sensor 5v |
Pin 20 – White | Yellow – pin e tps # 1 |
Pin 23 – Brown | Black – pin a/d sensor ground |
Pin 24 – Yellow/green | Orange – pin c/f sensor 5v |
Holley Key on power- UPDATE recommend to use the cigarette lighter fuse at fuse 8 with a fuse tap for a key on ignition source.
- E90 connector x6011 pin 6 green/white. Check this with a test light with the key on, you should have 12v, key off no power.
BMW cooling fan to holley connections
- The BMW cooling fans power and ground connections are not modified but the speed control is done by a single pwm control wire.
- You will need to configure a custom output in the Holley software to be a PWM signal to control the speed of the BMW fan.
BMW X600001 | Holley IO harness |
Pin 8 – black/blue | 1 of the 4 grey output wires |
BMW starter CAS to brake switch mods
This is required on an automatic car to get the factory start button functioning, factory manual cars staying manual will not need this step. Factory manual cars going automatic will be at the end of this section
- Connect pin 4, brake light signal, on connector X60001 to:
Depending on if your car was automatic or manual, 325i or 335i, this wire can change. You are looking for the wire that eventually goes to pin 41 on the cas.
On pre 03/07 cars this is most commonly pin 1, blue/black on connector X6031. On post 03/05 with the 12 wire x6031 this is pin 5 blue/black wire on X6031. Please be sure to make SURE this goes to pin 41 on the CAS, you don't want to send 12v into the wrong wire
- This will send a 12v brake signal to pin 41 on the CAS when the brake pedal is pressed.
- Connect a 10ga wire from pin 3(pre 03/07) or pin 1 (post 03/07) larger gauge black wire on X6011 to your starter solenoid connection.
Manual transmission car going automatic will need to do the following. There is a blue-brown wire (pin 18) on the DME connector x60001, that wire needs to get connected to the blue-red wire (pin 4) on the same connector which is the brake signal. Then, on the clutch switch you can remove the connector and connect the blue-brown wire to the blue-black wire. What this is going to do is send the brake signal from the dme connector, to the blue brown on the old clutch switch, to the blue black, which is to the cas pin 41.
BMW Automatic Transmission PT Can bus termination
- This is required on an automatic car to keep the PT can network functional. Without this many issues will come up but the most notable is the windshield wipers will never turn off.
- On connector x6021, connect pin 1 to 3 and 2 to 4. This will connect the red to red wire and the blue/red to the blue/red wire.
X60001
Pin assignments at plug connector X60001
Pin | Type | Description /Signal type | Connection /Measuring notes |
1 | E/A | Signal PT-CAN low | Powertrain CAN-bus |
2 | E | Start signal | Car access system |
3 | E/A | BSD signal | Battery sensor |
4 | E | Brake light signal | Brake light switch |
5 | A | Signal, exhaust flap | Exhaust flap |
6 | E | Signal Temperature sensor at radiator outlet | Temperature sensor at radiator outlet |
7 | E | Signal Accelerator pedal module | Accelerator pedal module |
8 | A | Signal Electric fan | Electric fan |
9 | A | Activation | Radiator shutter drive unit |
10 | M | Ground Accelerator pedal module | Accelerator pedal module |
11 | A | Supply Accelerator pedal module | Accelerator pedal module |
13 | A | Activation Secondary air pump relay | Secondary air pump relay |
14 | E/A | Signal PT-CAN high | Powertrain CAN-bus |
15 | E | Signal, electronic vehicle immobilizer | Car access system |
16 | E | Brake light test signal | Brake light switch |
17 | E | Signal, rear right wheel speed | Connector X10186 (rear right wheel speed) |
18 | E | Signal, clutch switch | Clutch switch module |
19 | E | Signal Temperature sensor at radiator outlet | Temperature sensor at radiator outlet |
20 | E | Signal Accelerator pedal module | Accelerator pedal module |
21 | E/A | TD signal | Connector TD signal |
22 | E | Supply, terminal 15 | Car access system |
23 | M | Ground Accelerator pedal module | Accelerator pedal module |
24 | A | Supply Accelerator pedal module | Accelerator pedal module |
25 | E | USA Signal Secondary air - hot-film air-mass meter | Secondary air - hot-film air-mass meter |
26 | A | Signal, E-box fan | E-box fan |
e90